Assembly Guide - Fitting Fabric Graphic to TexFrame

Assembly Guide - Fitting Fabric Graphic to TexFrame

This guide will provide you with the knowledge required to affix your fabric graphic to an assembled TexFrame.

While there are differences between the profiles of our extrusions the method used to insert the printed fabric graphic is extremely similar for all of them, so we've grouped them to make things easier (the frame used in this case was a 3D TexFrame).

Inserting a fabric graphic into extrusion is fairly straightforward, however like most things, it does get easier with experience. If at any time you find that you're not happy with your progress/finished product there's no harm in removing the graphic from the frame and starting again. Even a large, complex frame with straights & curves should take roughly 30mins for a single person to install. So it's best to take the time, if necessary, to get it looking right rather than to go for the quick install.



Step 1:

The very first step is to insert the graphic's corners/silicon strip into the corners of the extrusion.

TexFrame Fabric Corner Insert

Step 2:

Repeat Step 1 for all corners. Insert the silicon strip roughly 50-100mm away from the corner.

TexFrame Fabric All Corner Insert

Step 3:

Take the middle of the silicon length and insert it into the extrusion. 

Do this for 4 sides.

TexFrame Fabric Middle Insert

Step 4:

Now repeat Step 3 and insert the middle of the silicon lengths that remain.

Note: this step isn't super important for smaller frames (generally anything under 1000mm in length). However for larger frames this will ensure that the silicon is stretched evenly along the extrusion and that tension is applied to the graphic as evenly as possible. Depending on the size of your frame you may need to repeat this step several times!

TexFrame Fabric Middle Insert

Step 5:

Insert the remaining sections into the extrusion.

For a neat finish gently run your fingers along the edge of the silicon/extrusion to feel for any sections of silicon that are raised so they can be pushed in.

TexFrame Fabric Full Insert

Step 6:

To tidy up any corners which may be poking out, gently use the supplied allen key to ease the corner under (towards the silicon strip).

TexFrame Fabric Tidy Corner

Removing The Graphic:

This is a little tip coming from our experience, this can help with all extrusion however we find it much more useful (almost necessary) for the easy removal of frabric from our 3D TexFrame extrusion.

Gently insert the allen key, at the corner of the frame, at a slight angle. The goal is to get it under the silicon strip. Gently pry the silicon from the extrusion's channel.

It's also very important that when you remove your graphic you don't pull at the fabric to remove it. Rather try to get a good hold of the silicon strip and use that to remove the graphic. 

Pulling at the fabric alone could damage/stretch the fabric, the sewing that attaches the silicon to the fabric or (at the very least) make the fabric dirty.

TexFrame Fabric Corner Remove

Related Articles

Assembly Guide - 3D TexFrame
This guide will provide you with the knowledge required to assemble our 3D TexFrames - in this instance we'll be using a 700mm x 700mm x 700mm cube to demonstrate this. When you purchase a TexFrame system from us all that you need will be supplied! For each cube display there will be: 12 x 3D extrusion lengths (cut to the size you require) 8 x 3D extrusion corners 1 x alen key     Step 1: To begin; lay out one side of the cube as we have done. It's worth noting that the corners and the straigh..
Assembly Guide - Double Sided (D46) Curved TexFrame
This guide will provide you with the knowledge required to assemble our Double Sided (D46) TexFrames - in this instance we'll be using a custom built frame to demonstrate this. When you purchase a TexFrame system from us all that you need will be supplied! For this display there will be: 2 x 2000mm straight extrusion lengths (these are for the sides of the frame) 4 x curved extrusion lengths with a radius of 1500mm (these are for the top & bottom of the frame; 2 lengths will have holes in them indicating that these lengths will be used for the bottom of the frame ..
Latest Articles - All Articles

Welcome to the March 2018 Newsletter

Dear Customer,

In this issue of the newsletter, we'd like to show you an example of exhibition displays built with T-FPU Modular Exhibits , our TexFrame Fabric Pop-Up portable modular display solution.

ADI Displays is heading to Brisbane. You are invited to visit us at Visual Impact Brisbane 2018. 

A quick reminder: Only one week left to save 20% on BANNERADâ„¢ Retractable Banner Stand when ordering ADI Displays Online Store

Retractable Banner Stand, also known as Pull-Ups, is the most well known portable display product in the market.  The BANNERAD range of Pull-Ups is covering all types of customers application, preference and budget. Each model is uniquely designed and offering better values and meet the requirements of each customer.  The S Series is the starting model in the BANNERAD Retractable Banner range. S Series is built with a simple mechanism. There are more aluminium materials used for the construction of the S Series throughout the body, top-rail connection, feet and the internal rol..
Articles Menu

Contact Us

02 8518 1950
02 9533 3881